RE: [rp-ml] High Glass Transition (Tg) materials required

No problem Jason

Yeah it's odd...I've used it in applications a lot higher than that, and a thermal postcure will raise it a bit more

There's also an FDM material that might get close for you depending on the application
Click on the PPSF far right http://www.fortus.com/FDM_material_comparison.aspx

As for the PEEK, has anyone got that working properly yet?....I would have thought the cost would be a bit prohibitive for most applications.

Regards

Pat

________________________________
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On Behalf Of Jason Barkla
Sent: 13 December 2010 22:45
To: rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

Thanks Pat,

Ahh, I hadn't read Bob's post below properly, he did reference DSM and 3DS (sorry Bob). Unfortunately about the same as the DSM material, 83C.

Regards,

Jason Barkla
Manager - Rapid Parts

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd

________________________________
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On Behalf Of Warner, Pat
Sent: Tuesday, 14 December 2010 9:29 AM
To: Jason Barkla; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required
That's the data sheet for nanoform rather than nanotool

Try this http://3dsystems.com/products/materials/sla/accuraBluestone.asp

________________________________
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On Behalf Of Jason Barkla
Sent: 13 December 2010 22:28
To: rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

Thanks Bob,

Had checked that one out, maximum 80C.

Regards,

Jason Barkla
Manager - Rapid Parts

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd
145 Abbotts Rd
Dandenong Sth, VIC 3175
Australia
Learn more about us at:

http://www.rapidparts.com.au<http://www.rapidparts.com.au/>

http://www.awbell.com.au<http://www.awbell.com.au/>

Ph. +61 3 9799 9555
Fax. +61 3 9799 9666

________________________________
From: Bob Olsen [mailto:BOlsen@co.spectrumplasticsgroup.com]
Sent: Tuesday, 14 December 2010 9:20 AM
To: Jason Barkla; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required
Jason, DSM Somos and 3D offer SLA composite resins that might work. Here's a link to Somos ( Nanotool) , the 3D resin is called Bluestone.

http://www.dsm.com/en_US/downloads/dsms/datasheets/s15120product_data_sheet.pdf

Regards, Bob ( Protogenic Div, Spectrum Plastics Group)

________________________________
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On Behalf Of Jason Barkla
Sent: Monday, December 13, 2010 3:14 PM
To: rp-ml@rapid.lpt.fi
Subject: [rp-ml] High Glass Transition (Tg) materials required
Hi All,

Can anybody advise me of RP materials (and associated processes) that have a Glass Transition (Tg) temp of 200 degrees C (392F) or higher?

Regards,

Jason Barkla
Manager - Rapid Parts

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd
145 Abbotts Rd
Dandenong Sth, VIC 3175
Australia
Learn more about us at:

http://www.rapidparts.com.au<http://www.rapidparts.com.au/>

http://www.awbell.com.au<http://www.awbell.com.au/>

Ph. +61 3 9799 9555
Fax. +61 3 9799 9666

-------------------------------------------
For further information on the Renault F1 Team visit our web site at www.renaultf1.com. Renault F1 Team Limited Registered in England no. 1806337 Registered Office: 16 Old Bailey London EC4M 7EG WARNING: please ensure that you have adequate virus protection in place before you open or detach any documents attached to this email. This e-mail may constitute privileged information. If you are not the intended recipient, you have received this confidential email and any attachments transmitted with it in error and you must not disclose copy, circulate or in any other way use or rely on this information. E-mails to and from the Renault F1 Team are monitored for operational reasons and in accordance with lawful business practices. The contents of this email are those of the individual and do not necessarily represent the views of the company. Please note that this e-mail has been created in the knowledge that Internet e-mail is not a 100% secure communications medium. We advise that you understand and observe this lack of security when e-mailing us. If you have received this email in error please forward to: is.servicedesk@uk.renaultf1.com quoting the sender, then delete the message and any attached documents
-------------------------------------------

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________
Received on Tue Dec 14 00:36:27 2010