RE: [rp-ml] High Glass Transition (Tg) materials required

From: Jason Barkla <Jason_at_awbell.com.au>
Date: Tue Dec 14 2010 - 01:17:01 EET

Thanks Pat,
 
That FDM PPSF fits the bill, pity it won't run on our old FDM Vantage S.
 

Regards,
 
Jason Barkla
Manager - Rapid Parts

 

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd

________________________________

From: Warner, Pat [mailto:Pat.Warner@uk.renaultf1.com]
Sent: Tuesday, 14 December 2010 9:47 AM
To: Jason Barkla; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

No problem Jason

 

Yeah it's odd...I've used it in applications a lot higher than that, and
a thermal postcure will raise it a bit more

 

There's also an FDM material that might get close for you depending on
the application

Click on the PPSF far right
http://www.fortus.com/FDM_material_comparison.aspx

 

 

 

As for the PEEK, has anyone got that working properly yet?....I would
have thought the cost would be a bit prohibitive for most applications.

 

 

Regards

 

Pat

 

________________________________

From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Jason Barkla
Sent: 13 December 2010 22:45
To: rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

 

Thanks Pat,

 

Ahh, I hadn't read Bob's post below properly, he did reference DSM and
3DS (sorry Bob). Unfortunately about the same as the DSM material, 83C.

 

Regards,

 

Jason Barkla

Manager - Rapid Parts

 

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd

 

________________________________

From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Warner, Pat
Sent: Tuesday, 14 December 2010 9:29 AM
To: Jason Barkla; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

That's the data sheet for nanoform rather than nanotool

 

Try this http://3dsystems.com/products/materials/sla/accuraBluestone.asp

 

________________________________

From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Jason Barkla
Sent: 13 December 2010 22:28
To: rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

 

Thanks Bob,

 

Had checked that one out, maximum 80C.

 

Regards,

 

Jason Barkla

Manager - Rapid Parts

 

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd
145 Abbotts Rd
Dandenong Sth, VIC 3175
Australia

Learn more about us at:

 

http://www.rapidparts.com.au <http://www.rapidparts.com.au/>

 

http://www.awbell.com.au <http://www.awbell.com.au/>

 

Ph. +61 3 9799 9555
Fax. +61 3 9799 9666

 

 

________________________________

From: Bob Olsen [mailto:BOlsen@co.spectrumplasticsgroup.com]
Sent: Tuesday, 14 December 2010 9:20 AM
To: Jason Barkla; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] High Glass Transition (Tg) materials required

Jason, DSM Somos and 3D offer SLA composite resins that might work.
Here's a link to Somos ( Nanotool) , the 3D resin is called Bluestone.

 

http://www.dsm.com/en_US/downloads/dsms/datasheets/s15120product_data_sh
eet.pdf

 

Regards, Bob ( Protogenic Div, Spectrum Plastics Group)

 

________________________________

From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Jason Barkla
Sent: Monday, December 13, 2010 3:14 PM
To: rp-ml@rapid.lpt.fi
Subject: [rp-ml] High Glass Transition (Tg) materials required

Hi All,

 

Can anybody advise me of RP materials (and associated processes) that
have a Glass Transition (Tg) temp of 200 degrees C (392F) or higher?

 

Regards,

 

Jason Barkla

Manager - Rapid Parts

 

Rapid Parts (Worldwide) a division of A.W.Bell Pty Ltd
145 Abbotts Rd
Dandenong Sth, VIC 3175
Australia

Learn more about us at:

 

http://www.rapidparts.com.au <http://www.rapidparts.com.au/>

 

http://www.awbell.com.au <http://www.awbell.com.au/>

 

Ph. +61 3 9799 9555
Fax. +61 3 9799 9666

 

-------------------------------------------
For further information on the Renault F1 Team visit our web site at
www.renaultf1.com. Renault F1 Team Limited Registered in England no.
1806337 Registered Office: 16 Old Bailey London EC4M 7EG WARNING: please
ensure that you have adequate virus protection in place before you open
or detach any documents attached to this email. This e-mail may
constitute privileged information. If you are not the intended
recipient, you have received this confidential email and any attachments
transmitted with it in error and you must not disclose copy, circulate
or in any other way use or rely on this information. E-mails to and from
the Renault F1 Team are monitored for operational reasons and in
accordance with lawful business practices. The contents of this email
are those of the individual and do not necessarily represent the views
of the company. Please note that this e-mail has been created in the
knowledge that Internet e-mail is not a 100% secure communications
medium. We advise that you understand and observe this lack of security
when e-mailing us. If you have received this email in error please
forward to: is.servicedesk@uk.renaultf1.com quoting the sender, then
delete the message and any attached documents
-------------------------------------------

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________
Received on Tue Dec 14 01:01:52 2010

This archive was generated by hypermail 2.1.8 : Fri Mar 11 2011 - 05:24:19 EET